1933-34 Repro Floormats

Started by oldplym, April 30, 2008, 06:16:14 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

TodFitch

On the two door sedan the front bucket seats are held in place by a rod that runs through a pair of attachment points at the front of each seat. The seat is free to pivot forward on the rod. This allows you to have access to the rear seat area. It also exposes the floor when the seat is tilted. So you need either the front rubber mat to extend to the rear or you need the rear carpet to extend to the front to cover the floor under the bucket seats.

I don't really know where that transition is supposed to be but at present I have it at the back of the front seats.

The last remnants of my original factory floor mat disappeared in a move over 30 years ago so I don't have that to reference. However the ribbed piece of matting that I cut at around that same time to use as a floor mat extends to the rear of the front seats. I am guessing that I cut the replacement mat to the same general dimensions as the original but time has erased my memory on that exact point.

I could argue that rubber matting was cheaper than carpet so it would make sense to use it under the front seats. But I have nothing to back it up. Other than the fact that the part numbers are different for the front matting. I am away from my parts book at the moment but if the rear carpet part numbers are the same for the four door and two door that would lend credence to the theory that the matting should extend to the rear of the front seats.

After I did my interior I got in contact with a fellow that had a PD two door with an original interior. I don't have his photos on my laptop at the moment and the photos of his I posted to my web site do not show that detail. I'll have to check my photo archive to see if there were any that show where the transition from rubber to carpet takes place.
  •  

oldplym

Tod:
This is really curious.  I never looked for it before, but you are correct, it appears the 2-dr is different from the coupe and 4-dr.  The parts book lists different part numbers.  Do you happen to know what the difference is?  Is it related to the fact the 2-dr has two seats up front?  I would have thought all were the same since the coupe mat seems to end upon contacting the seat adjustment rail blocks.  I would have thought this overall distance would be the same on any '33 regardless of the number of seats.  Must be something else.  Please educate me.

Don
  •  

TodFitch

Quote from: Buddy Romines on May 05, 2008, 09:06:00 AM
Good Morning:

When you guys are saying "Floor Mats", are you refering to a "Complete Floor Cover"?? Or, are you refering to 4 mats that protect the floor covering, wheather it is rubber or carpet?

Enjoy your old car...? ? Buddy...

The part in question is the large rubber mat that covers the area between the front seat and the firewall. Apparently in a coupe there are some other pieces too for between the door and the seat and for behind the seat, however those are not part of this topic.

The original front floor mat had a ribbing pattern similar to what is found on the brake lever hole pad but this "reproduction" part has 1/8 inch ribs. This might be a good thing for me as it implies that a similar mat could be made in a longer length. (In my case the front floor mat is different for a two door sedan than it is for a coupe or four door sedan so what works for others may not be sufficient for my needs.) However if you have a coupe or four door sedan then finding an unused older reproduction from N/C Industries (no longer manufactured) might be better.
  •  

Buddy Romines

Good Morning:

When you guys are saying "Floor Mats", are you refering to a "Complete Floor Cover"?  Or, are you refering to 4 mats that protect the floor covering, wheather it is rubber or carpet?

Enjoy your old car...    Buddy...
  •  

TodFitch

I have a reply back from Terry Kesselring. Apparently his phone number is 859-689-9900, not the number given on the first post of this thread.

The floor mat used as a prototype is from a PE coupe and the holes for things like the shift lever are not fully cut out so that you can make the cuts to exactly match your car.
  •  

TodFitch

Thanks for the heads up!

I have already sent him an email requesting price and availability information.
  •  

oldplym

Just to give interested parties "heads up", the Antique Auto Shop in Hebron, Kentucky is offering reproduction floormats for the 1933-34 Plymouths.  If you're interested, contact Terry Kesselring at 859-342-8363 or e-mail him at .  In the future he will be advertising in the Bulletin and will also have some pictures.  I had no way of telling him what kind of response to expect but this has been a highly sought after part in the past. 

As I said, just a "heads up" everyone.

Don
  •