my interesting brake problems

Started by merry_prankster, March 22, 2008, 11:52:14 PM

Previous topic - Next topic

0 Members and 0 Guests are viewing this topic.

merry_prankster

It's not fixed yet, but atleast now I know what the problem is. I pulled the master cylinder apart just to be sure and there was a washer in the wrong spot. Doh! I put it all back together and the relief port was still covered. Having saved all my reciepts, I called the place where I got the rebuild kit from and what do you know it didn't come with a new spring. So, odds are the old spring that I was reusing didn't have enough oomph left to push the piston back far enough. Now I just have to find a new spring.
  •  

merry_prankster

I've since gotten new wheel cylinders all around. I took a short drive after I thought I had it the last time and discovered that a couple of them were sticking. I also got new brake hoses and return springs all around. My box of goodies also had a service manual in it, so now I have an exploded view of the innards of the master cylinder. Hopefully when I pull tht apart again just to reassure myself, things are in there in the correct order. Probably not because I can see the valve through the return hole, but atleast I know what I'm looking at now.
  •  

Tim B

How 'bout brake hoses?  If they're collapsing internally, they won't allow the fluid to return to the master cylinder and will hold the brakes out.
Tim Bowers
Stellar Antique Auto Restorations
  •  

Don Coatney

If your brake fluid was "chunky" I would suggest you do more bleading and or remove the master cylinder
and clean it. The hole in question is the small one that has a prick punch in it in the second picture. The
"chunks" in your brake fluid will plug this hole up and not allow the fluid to return to the master cylinder.


Don Coatney
  •  

Ken Bartz

They are right about the hole in the master cylinder.  To make sure that this hole gets open when the petal is returned to the top position I have put a wire into the hole.  You can easily tell if the hole is open when the wire goes to the bottom of the master cylinder.  Don't get carried away with adjusting this push rod as you can adjust it too far.  Now, I can say I had this very problem with my 40 Plymouth.  The longer you drive the tighter the petal gets.  I even drove (to get home) with the rear brakes smoking.  I found the problem to be the valve at the bottom of the master cylinder.  But you say that the master cylinder has been rebuilt.  Buy all new and rebuild it again.  This has to be the problem!
Ken Bartz
1940 PLymouth business coupe
1951 Plymouth club coupe
1952 Plymouth business coupe
  •  

merry_prankster

Sadly, after putting about 15 miles on it my problems have returned. I was really hoping I could stay away from the wheel cylinders because I don't have the tools to rehone them. Also I discovered that the rebuild kits would cost about 2/3 of the price of new ones. So new wheel cylinders it is. Guess tires will have to wait.
  •  

merry_prankster

Thanks to a break in the weather I was able to sneak under the car and found the adjuster mentioned. Good thing I'm skinny :D I backed it off about 1/4" and now there's about an inch of pedal movement before I feel contact to the cylinder piston. I took it out for about a 6 mile spin and the brakes didn't seem to be dragging at the end. It was a little hard to get moving from the last stop light, but that could just be me.

Hopefully my brake problems are fixed. I'll go for a longer drive later. Gotta seach for tires....wheeee

thanks for the advice guys.
  •  

merry_prankster

That makes sense. Guess I'll have to pull the floor pan and see if there's an adjustment on the rod. I don't remember there being one, but it's been awhile since I've looked at it.
It seems that all of the local auto parts stores that I've been to don't carry brake parts for my car. Not suprised really.

Unfortunately the oregon liquid sunshine is falling today and I don't have a covered area to work in, so it may be a few days before I can look. I will post again if i figure it out or not.
  •  

Wm Steed

The building and retention of pressure in the hydraulic brake system is pretty much as stated by the earlier postings to this topic. Many times the problem is caused by a defective master cylinder, the wrong cylinder for the vehicle and/or the wrong rod from the peddle assembly. Some MC rods are adjustable, other are not. The MC rod has to be short enough to allow free travel between the rod and the MC piston.

I like others, have found out the hard way that simple problems turn into big deals when someone sells you a part that falls into the category of 'one size fit's all' ...Bill
39 Plym. Conv. Coupe
  •  

TodFitch

Quote from: p4jim on March 23, 2008, 12:31:34 AM
My 37 did the same thing.? The small hole just in front of the master cylinder piston cup was obstructed.? In my case I had lengthened the push rod too far and caused the rubber cup to overlap the hole.
Good Luck, P4jim

Been there. Done that.

The piston in the master cylinder must return far enough to clear that relief hole (adjustment of brake pedal rod). And the hole must not be plugged.
  •  

p4jim

My 37 did the same thing.  The small hole just in front of the master cylinder piston cup was obstructed.  In my case I had lengthened the push rod too far and caused the rubber cup to overlap the hole.
Good Luck, P4jim
  •  

30U sedan

Need more information.......
What year? ???
Power assist? ???

  •  

merry_prankster

Here's what happens:

Start the car and have about 3" of play on the pedal, brakes work very well.
Drive for about 10 minutes and I have about 2" of play, brakes work well still.
Drive another 10 minutes and there's no play on the pedal, feels like shoes are dragging in the drums.
At this point, if I stop at all I'm stuck there until the system bleeds down enough for my to move and pray I don't have to stop again. :-\

What I've done so far:

Vaccuum out all the old brake fluid and replace with new. Did this twice because the original fluid was kinda chunky. I love my air powered bleeder. ;D No change in brakes.

Rebuild master cylinder. All the fittings were in suprisingly good shape and the bore was smooth, no internal rust. Made absolutely sure parts went in in correct order. Second rebleed here. No change in brakes.

Pulled drums off to inspect for wear, pitting and groves. Strangely no problems here either. Marks in drums from a shop that turned them about 3 years ago and new shoes all around. Found some rust, dirt and cobwebs on the back plate, no shock there. The only thing I find odd is the front shoes have 2 return springs each and the rears have 1 each. I checked www.oldmoparts.com and thier parts catalogue says that this is correct. The springs are a bit rusty and I intend to replace them all just in case.

I'm a harley mechanic so hydraulic drum brakes aren't really a stretch from what I deal with at work (harley used to use them ages ago). If any of you have a suggestion or helpful advice I'd like to hear it.

It's not in knowing everything, it's knowing the right person to ask.
  •